Supports SIP, Dante®, 4 configurable mic/ line audio inputs, 8 configurable mic/line audio outputs, built-in USB audio, and a Telco interface.
Key Highlights
- Built-in Native Camera Tracking for Unite cameras and many 3rd party cameras using RS-232 and Ethernet VISCA over IP.
- 4 mic/line inputs and 8 mic/line outputs
- Next-gen Acoustic Echo Cancellation (AEC) on every mic input.
- Support for SIP-based conferencing up to 5 lines and 5 calls based on line configuration.
- 16 Dante inputs and 16 Dante outputs for audio networking.
- Analog Telco interface.
- Native Audio based VISCA camera control
- Built-in USB audio.
- Reduced foot-print and power consumption.
- Built-in DARE™ algorithm for dynamic feedback elimination.
- C-Link and P-Link enable easy addition of DSPs and peripherals.
- Configure an entire system of C-linked DSPs with CONVERGE CONSOLE® AI software.
- Flexible control options include Touch-Panel Controller, BYOD dialer apps or 3rd party control modules.
- Noise Cancellation with Adaptive-Ambience.
- Daisy-chain the CONVERGE Pro 2 with the BMA 360, DIALOG® 20 USB 2-Channel Wireless Microphone System, and other peripheral devices through P-Link.
Applications
- SIP Conferencing
- POTS conferencing
- Audio recording
- Pre-recorded digital audio
- Audio networking over a LAN
- Web conferencing
- UC audio conferencing
- Sound reinforcement
- Bridge web conferences
Workspaces
- Conference rooms
- Training rooms
- Lecture halls
- Courtrooms
- Telemedicine theaters
- Houses of Worship
Supports SIP, Dante®, 4 configurable mic/ line audio inputs, 8 configurable mic/line audio outputs, built-in USB audio, and a Telco interface.
PART NUMBER
- 910-3200-008-D
CAMERA TRACKING
- Supported Cameras: Unite 150, Unite 200, Unite 160, Unite 260 (One Camera per DSP)
- Communication Protocol: VISCA
- Communication options: Serial (RS-232) or Ethernet (VISCA over IP)
MIC/LINE INPUTS & OUTPUTS
- Inputs: Balanced audio inputs, 3.81 mm Orange color Phoenix/Euroblock type male header, Push-on miniterminal block
- Outputs: Balanced audio outputs, 3.81 mm Black color Phoenix/Euroblock type male header, Push-on miniterminal block
- Frequency Response: 20 Hz – 22 kHz @ +4 dBu, +/- 0.5 dBu
- EIN (Equivalent Input Noise): 20 kHz BW, max gain, Rs = 150 Ω, -126 dBu
- THD + N (Total Harmonic Distortion + Noise):
- 20 Hz – 22 kHz @ +4 dBu, line level, 0.006%
- 20 Hz – 22 kHz @ -56 dBu, mic level, < 0.04%
- Dynamic Range: 20 Hz – 20 kHz @ 0 dB, >105 dB
- Crosstalk (Mic/Line): Channel to Channel, stimulus at 20 dBu to receptor at -56 dBu, 1 kHz, < -98 dB
- Input Impedance: Balanced (line to ground), 2.2 kΩ, 1%
- Nominal Input Level: Adjustable -56 dB to 0 dB, 7 dB step coarse gain
- Maximum Input Level: -65 dBu to 20 dBu
- Phantom Power: 48 V, Impedance 6.81 kΩ
- Output Impedance: Balanced (line to ground), 95 Ω, 1%
- Output Level: 0 dBu (Nominal), 20 dBu (Max), -40 dBu (Selectable)
USB AUDIO
- Port Type: USB-B connector
- Audio: Digital Audio, 2 x 2 bidirectional channels
- Sample Rate: 48 kHz
- Sample Bit Depth: 24-Bit
- Compatible: USB 2.0, USB 3.0
TELEPHONE
- Port Type: RJ-11
- Frequency Response:
- Mic/Line Input to Telephone Out: 250 Hz – 3.4 kHz, +/- 2dB, 4 dBu
- Telephone In to Mic/Line Out: 250 Hz – 3.4 kHz, +/- 2 dB, -15 dBu
- THD + N:
- Mic/Line Input to Telephone Out: 67 dBu
- Telephone In to Mic/Line Out: > 87 dBu
- Dynamic Range:
- Mic/Line Input to Telephone Out: > 67 dBu
- Telephone In to Mic/Line Out: > 87 dBu
- REN: Ringer Equivalent Number 0.2
- Transhybrid Balance: 30 dB (1 kHz, all AC terminations)
SIP
- Port Type: RJ-45, 10/100 Mbps Ethernet Network, Auto Negotiation
- Audio: 5 Lines
- Codec: G.711 uLaw, G.711 ALaw, G.722
ETHERNET
- Port Type: RJ-45, 10/100 Mbps Ethernet Network, Auto Negotiation
- IP address: IPv4 (IPv6 upgradeable through future s/w, f/w upgrade)
DANTE™ and AES67 AUDIO
- Port Type: RJ-45 Gigabit Ethernet connectors for Primary and Secondary Ports
- Audio: Digital Audio, 16 x 16 bidirectional channels
- Sample Rate: 48 kHz / 96 kHz
- Sample Bit Depth: 24-Bit
- AES67 Mode: Enabled through Dante controller software
C-LINK EXPANSION BUS
- Ports Type: RJ-45 (Cat 5e or Cat 6)
- C-Link In & Out: Proprietary Expansion Bus
- Audio: 64 Expansion channels
- Cable: Solid core, factory terminated Cat 5e or 6 cable
- Distance:Up to 80 ’ (24 m)
P-LINK PERIPHERAL BUS
- Ports Type: RJ-45 (Cat 5e or Cat 6)
- P-Link In & Out: Proprietary Peripheral Bus
- PoE In:
- P-Link In Port
- PoE 802.3 af Mode B, Midspan
- Power on “spare pairs” 4, 5 and 7, 8
- Input voltage range: 48 V to 56 V
- Audio: Up to 3 BMA CT units + up to 3 DIALOG 20 Wireless Receiver units + Up to 3 USB Expander units + Up to 3 GPIO Expander units
- Cable: Solid core, factory terminated Cat 5e or 6 cable
- Distance: Up to 200’ (60 m)
RS-232
- Port Type: DB9 Female
- Settings: 9600/19200/38400/57600/115200 Baud; Serial Echo; Flow Control
- Support: Serial commands
GPIO
- Port Type: 5.08 mm Green color Phoenix/Euroblock type male header
- Support: Control, Status, Variable Voltage Control
- Power Pin: 5 VDC @ 350 mA Power Source
- Pin 1 to 4:
- Open Collector Outputs: 40 VDC @ 250 mA
- Active Outputs (Source/Sink): 5 VDC @ 25 mA
- Logic Inputs: 40.2 kΩ pull up
- Variable Voltage Control Inputs: 5 VDC max
- Ground Pin: GND
USB CONTROL
- Port Type: USB-B connector
- Location: Front Panel
- Compatible: USB 2.0, USB 3.0
LEDs
- Location: Front Panel
- Status LED:
- Off: Unit still initializing
- Blue – Fast Blinking: Stack Syncing in progress
- Blue – Slow Blinking: Unit not configured
- Blue – Solid: Configured unit
- Red – Fast Blinking: Stack Sync error
- Locate LED: Blue – Blinking: Unit “Locate” command received
- Power LED: Blue – Solid: Unit is powered on
POWER & THERMAL
- Port Type: AC Inlet
- Mains Voltage: 100-240 VAC, 50/60 Hz
- Power Consumption: 50 Watts Typical
- Thermal: 170 BTU/Hr Typical
- Operating Temperature: 14 °F (-10 °C) to 104 °F (40 °C) Ambient Temperature
DIMENSION & WEIGHT
- RU size: 1 RU
- Width x Depth x Height:
- Without rack-ears: 17.1 x 10.7 x 1.7 ” (431 x 273 x 44 mm)
- With rack-ears: 19.1 x 10.7 x 1.7 “ (483 x 273 x 44 mm))
- Unit Weight: 9.3 lbs (4.2 Kg) (Approximately)
- Shipping Weight: 13.8 lbs (6.3 Kg) (Approximately)
PACKAGE
- Power Cord: 6’ (1.8 M), Grounded, Qty 1
- Input Connectors: Terminal Block Connector, 4 Position (Orange), Qty 4
- Output Connectors: Terminal Block Connector, 3 Position (Black), Qty 8
- GPIO Connector: Terminal Block Connector, 6 Position (Green), Qty 1
- C-Link Cable: RJ-45 To RJ-45 Cable, 18” (45.7 cm), Qty 1
- Network Cable: RJ-45 To RJ-45, 7 ’ (2 M), Qty 1
- USB Cable: USB Type A to Type B, 6 ’ (1.8 M), Qty 1
- Rack Ears: Pre-installed, Qty 2
- Screw/Washer Kit: Rack Decor, Qty 4
CONVERGE® Pro 2 128VT FAQs
The main distinction is that the 48VTD includes Dante audio networking capability with 16 Dante inputs and 16 Dante outputs. Both models feature 4 mic/line inputs, 8 mic/line outputs, SIP conferencing support, and an analog Telco interface, but the 48VTD’s Dante integration allows for expanded audio networking over LAN.
The CONVERGE Pro 2 48VTD offers multiple audio connection options including:
4 mic/line inputs
8 mic/line outputs
16 Dante inputs
16 Dante outputs
Built-in USB audio
Analog Telco interface
SIP interface supporting up to 5 lines and 5 calls
The system includes the built-in DARE™ (Dynamic Adaptive Response) algorithm for dynamic feedback elimination. Combined with the Native Audio based VISCA camera control and professional DSP algorithms, it ensures high-quality audio performance across various applications, from conferencing to sound reinforcement.
Yes, the 48VTD offers extensive integration options through:
C-Link and P-Link for adding DSPs and peripherals
P-Link daisy-chaining with devices like the BMA 360 and DIALOG 20 Wireless Microphone System
Built-in Native Camera Tracking for ClearOne Unite and third-party cameras
Dante networking for connection with other Dante-enabled devices
Multiple control options including Touch-Panel Controller, BYOD dialer apps, and third-party control modules